43-1088_90.fm Page 1 Tuesday, August 17, 1999 2:57 PM
Cat. No. 43-1088/1090
OWNER’S MANUAL
Please read before using this equipment.
900-MHz Cordless Telephone
with Headset Jack
ET-918 White(43-1088)
ET-920 Black(43-1090)
43-1088_90.fm Page 3 Tuesday, August 17, 1999 2:57 PM
Important Note: Cordless phones
such as this one require AC power to
operate. When the AC power is off,
you cannot dial out or receive incoming
calls using your phone. To be safe, you
should also have a phone that does
not need AC power to operate (not a
cordless phone) so you can still make
and receive calls if there is an AC pow-
er failure.
READ THIS BEFORE
INSTALLATION
Each device that you connect to the
phone line draws power from the
phone line. We refer to this power draw
as the device’s ringer equivalence
number, or REN. The REN is on the
bottom of the base.
If you are using more than one phone
or other device on the line, add up all
the RENs. If the total is more than five,
your phones might not ring. In rural ar-
eas, a total REN of three might impair
ringer operation. If ringer operation is
impaired, remove a device from the
line.
We recommend you record your
phone’s serial number here. The num-
ber is on the bottom of the base.
Serial Number __________________
Warning: To reduce the risk of fire
or shock hazard, do not expose
this product to rain or moisture.
FCC STATEMENT
CAUTION
This telephone complies with Part 68
of FCC Rules. You must, upon re-
quest, provide the FCC Registration
Number and the REN to your phone
company. These numbers are on the
bottom of the base.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
Note: You must not connect your
phone to any of the following:
This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
• coin-operated systems
• party-line systems
• most electronic key phone sys-
tems
This symbol is intended to inform
you that important operating and
maintenance instructions are in-
cluded in the literature accompany-
ing this product.
!
3
43-1088_90.fm Page 4 Tuesday, August 17, 1999 2:57 PM
CONTENTS
Installation ............................................................................................................ 5
Selecting a Location ........................................................................................ 5
Placing the Base on a Desk Top ............................................................... 5
Mounting the Base on a Wall Plate ........................................................... 6
Mounting the Base Directly on the Wall .................................................... 7
Connecting and Charging the Battery Pack .................................................... 9
Setting the Dialing Mode ............................................................................... 11
Setting the Ringer Tone/Volume .................................................................... 11
Operation ............................................................................................................ 12
Making and Receiving Calls .......................................................................... 12
Selecting the Channel ................................................................................... 12
Setting the Handset Volume .......................................................................... 12
Using REDIAL ............................................................................................... 12
Using FLASH ................................................................................................. 13
Using Tone Services on a Pulse Line ............................................................ 13
Paging ........................................................................................................... 14
Memory Dialing .............................................................................................. 14
Storing a Number in Memory .................................................................. 14
Entering a Pause .................................................................................... 15
Dialing a Memory Number ...................................................................... 15
Chain-Dialing Service Numbers .............................................................. 16
Testing Stored Emergency Numbers ...................................................... 16
Using a Headset ............................................................................................ 16
Troubleshooting ................................................................................................. 17
Care and Maintenance ....................................................................................... 19
Replacing the Battery Pack ........................................................................... 20
The FCC Wants You to Know ........................................................................ 21
Lightning ........................................................................................................ 21
4
43-1088_90.fm Page 5 Tuesday, August 17, 1999 2:57 PM
INSTALLATION
• The USOC number of the jack to
be installed is RJ11C (RJ11W if
you want to mount it on a wall
plate).
SELECTING A
LOCATION
You can place the phone’s base on a
desk top or table, or mount it on a wall.
Select a location that is:
Placing the Base on a
Desk Top
• near an AC outlet
• near a telephone line jack
• out of the way of normal activities
Follow these steps when you place the
base on a desk, shelf, or table.
1. Plug one end of the supplied long
modular cord into the TEL LINE
jack on the back of the base.
• away from electrical machinery,
electrical appliances, metal walls
or filing cabinets, wireless inter-
coms, alarms, and room monitors
• away from other cordless phones
The base’s location affects the hand-
set’s range. If you have a choice of
several locations, try each to see
which provides the best performance.
Caution: The supplied RadioShack
AC adapter was designed specifically
for your ET-918/920. Use only the sup-
plied adapter.
2. Plug the modular cord’s other end
into a modular phone line jack.
Notes:
• Your telephone connects directly
to a modular telephone line jack. If
your phone line jack is not a mod-
ular jack, you can update the wir-
ing yourself, using jacks and
adapters available at your local
RadioShack store. Or, you can let
the phone company update the
wiring for you.
5
43-1088_90.fm Page 6 Tuesday, August 17, 1999 2:57 PM
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack
on the back of the base.
Mounting the Base on a
Wall Plate
1. Plug one end of the supplied short
modular cord into the TEL LINE
jack on the back of the base.
4. Route the adapter’s cord through
the strain relief slot on the base
(as shown).
Strain Relief
Slot
2. Route the modular cord through
the right slot on the bottom of the
base.
5. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.
6. Lift the base’s antenna to a verti-
cal position.
6
43-1088_90.fm Page 7 Tuesday, August 17, 1999 2:57 PM
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack
on the back of the base.
6. Press and lift out the handset
holder, turn it over and rotate it
180°, then snap it back into place
so it holds the handset.
4. Route the adapter’s cord through
the left side of the strain relief slot
on top of the base and through the
left slots at the bottom of the base.
7. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.
8. Lift the base’s antenna to a verti-
cal position.
Strain Relief
Slot
Mounting the Base Directly
on the Wall
For this mounting method, you need
two flat-head wood screws (not sup-
plied) with heads that fit into the key-
hole slots on the bottom of the base.
5. Plug the short modular cord into
the wall plate jack, press the
excess cord into the slot in the
center of the base, then align the
base’s keyhole slots with the wall
plate studs and slide the base
downward to secure it.
1. Drill two holes 315/16
3
16
/
inches apart. Then
thread a screw into
each hole, letting the
heads extend about
3/16 inch from the
wall.
315/16
Slot for
Excess
Cord
7
43-1088_90.fm Page 8 Tuesday, August 17, 1999 2:57 PM
2. Plug one end of the supplied long
modular cord into the TEL LINE
jack on the back of the base.
5. Route the adapter’s cord through
the left side of the strain relief slot
on top of the base and through the
left slots on the bottom of the
base.
Strain Relief
Slot
3. Route the modular cord through
the right slots on the bottom of the
base.
6. Align the keyhole slots with the
mounting screws and slide the
base downward to secure it.
4. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack
on the back of the base.
7. Plug the modular cord into a mod-
ular phone line jack.
8
43-1088_90.fm Page 9 Tuesday, August 17, 1999 2:57 PM
8. Press and lift out the handset
holder, rotate it 180°, then snap it
back into place so it holds the
handset.
2. Plug the battery pack’s plastic
connector into the socket in the
compartment. The connector fits
only one way.
Note: For easier battery pack con-
nection, lift it out of the compart-
ment, insert its connector into the
socket and replace the battery
pack inside the compartment.
9. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.
10. Lift the base’s antenna to a verti-
cal position.
3. Replace the cover, then reinsert
and tighten the screw.
CONNECTING AND
CHARGING THE
BATTERY PACK
To charge the battery pack, simply
place the handset on the base. The
CHARGE indicator on the base lights.
The phone comes with a rechargeable
nickel-cadmium battery pack in the
handset. Before using your phone, you
must connect the battery pack and
then charge it for about 14 hours.
1. Remove the screw on the battery
compartment cover, then press
down and slide the cover in the
direction of the arrow to remove it.
CHARGE Indicator
Recharge the battery pack when the
handset beeps and the TALK/BATT
LOW indicator flashes.
9
43-1088_90.fm Page 10 Tuesday, August 17, 1999 2:57 PM
Notes:
ing the handset off the base until
the TALK/BATT LOW indicator
flashes. Otherwise, the battery
pack loses its ability to fully re-
charge.
• If the CHARGE indicator does not
light when you place the handset
on the base, be sure the battery
pack and AC adapter are correctly
and securely connected.
• If the TALK/BATT LOW indicator
does not light and the phone does
not work, recharge the battery
pack. (The battery power might be
too low to light the indicator.)
Also, check the charging contacts
on the handset and the base. If
the contacts are dirty or tarnished,
clean them with a pencil eraser.
• If the battery pack becomes weak
during a call, you hear a beep ev-
ery 30 seconds and the TALK/
BATT LOW indicator flashes ev-
ery 3 seconds. Recharge the bat-
tery pack.
• If the battery pack is completely
discharged, the handset loses the
security access-protection code.
To reset the code, place the hand-
set on the base and charge the
battery pack.
• The supplied battery pack should
last for about a year. When the
battery pack loses its ability to
fully recharge, order a replace-
ment battery pack from your local
RadioShack store (see “Replacing
the Battery Pack” on Page 20).
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work
and you might hear an error tone.
If this happens, return the handset
to the base for a few seconds.
• About once a month, fully dis-
charge the battery pack by keep-
10
43-1088_90.fm Page 11 Tuesday, August 17, 1999 2:57 PM
SETTING THE DIALING
MODE
SETTING THE RINGER
TONE/VOLUME
DIAL MODE
Set
on the back of the base
You can select one of four different
ringer tone/volume settings while the
phone is not in use.
for the type of service you have. If you
are not sure which type you have, do
this test.
DIAL MODE
T
to .
1. Set
VOLUME
Press
to hear the current
ringer setting.
2. Lift the handset and listen for a
dial tone.
VOLUME
Repeatedly press
until you
hear the desired ringer setting. Each
VOLUME
0
3. Press any number other than .
time you press
changes in this order:
, the ringer
Note: If your phone system
requires that you dial an access
High-volume, high-pitch
9
code ( , for example) before you
dial an outside number, do not
press the access code either.
Low-volume, high-pitch
High-volume, low-pitch
Low-volume, low-pitch
If the dial tone stops, you have
DIAL
touch-tone service. Leave
MODE
T
set to .
If the dial tone continues, you
DIAL
have pulse service. Set
MODE
P
to .
11
43-1088_90.fm Page 12 Tuesday, August 17, 1999 2:57 PM
OPERATION
BATT LOW indicator blinks, and the
handset beeps, followed by a brief
pause as your phone searches for a
clear channel.
MAKING AND
RECEIVING CALLS
To make or answer a call, lift the hand-
set. Or, if the handset is not in place on
the base, press TALK. The TALK/
BATT LOW indicator on the handset
and the IN USE indicator on the base
light.
Note: If the handset is too far from the
base, the channel might not change.
Move closer to the base and try again.
SETTING THE HANDSET
VOLUME
To end a call, place the handset on the
base or press TALK so the TALK/BATT
LOW indicator turns off.
To change the volume you hear
through the handset, press VOLUME
during a call. The handset volume has
two settings, high or low.
TALK to hang up the
Note: If you press
phone and the phone does not discon-
nect, press TALK again while holding
the handset closer to the base or place
the handset on the base.
USING REDIAL
You can quickly dial the last number di-
aled. When you hear a dial tone, sim-
ply press REDIAL/P.
SELECTING THE
CHANNEL
The phone scans 40 channels (fre-
quency pairs used between the base
and the handset) and automatically se-
lects a clear channel each time you
make or receive a call.
If you hear other conversations or ex-
cessive noise during a call, press CH to
select a different channel. The TALK/
12
43-1088_90.fm Page 13 Tuesday, August 17, 1999 2:57 PM
Notes:
USING TONE SERVICES
ON A PULSE LINE
• The redial memory holds up to 32
digits, so you can redial long-
distance as well as local numbers.
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by follow-
ing these steps.
• The redial memory also holds
pause entries. See “Entering a
Pause” on Page 15.
• The redial memory does not store
a flash entry or any digits you
DIAL MODE
P
1. Be sure
is set to .
FLASH
press after
Flash”).
(see “Using
2. Dial the service’s main number.
3. When the service answers, press
TONE/
. Any additional numbers
you dial are sent as tone signals.
USING FLASH
FLASH
performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
4. After you complete the call, return
the handset to the base or press
TALK
. The phone automatically
resets to the pulse mode.
For example, if you have Call Waiting,
FLASH
press
to answer an incoming
call without disconnecting the current
FLASH
call. Press
first call.
again to return to the
Note: If you do not have any special
FLASH
phone services, pressing
disconnect the current call.
might
13
43-1088_90.fm Page 14 Tuesday, August 17, 1999 2:57 PM
PAGING
MEMORY DIALING
To page the person who has the hand-
set or to locate the handset when the
You can store up to 10 numbers in
memory, then dial a stored number by
pressing a one-digit memory location
number.
PAGE
phone is not in use, hold down
on the base for at least 2 seconds. The
handset beeps for 1 minute. To stop it
TALK
from beeping sooner, press
the handset twice.
on
Each number you store can be up to
16 digits long.
Storing a Number in Memory
Note: An error tone sounds and the
phone exits the programming mode if
you wait more than 20 seconds be-
tween each key press.
1. Lift the handset. If the TALK/BATT
TALK
LOW indicator lights, press
to turn it off.
MEM
2. Press
. The TALK/BATT LOW
indicator blinks.
Notes:
• The phone goes off-hook (you
hear the dial tone) the first time
TALK
you press
set from beeping. If you do not
TALK
to stop the hand-
press
again, the phone re-
mains off-hook.
PAGE
• If you press
for less than 2
seconds, the handset beeps for
only 2 seconds.
TONE/
3. Enter the number and any
REDIAL/P
mode changes or
entries (see “Entering a Pause” on
Page 15).
14
43-1088_90.fm Page 15 Tuesday, August 17, 1999 2:57 PM
TALK
if the
Notes:
Or, lift the handset, press
TALK/BATT LOW indicator lights, and
MEM
TONE/
REDIAL/P
• Each
or
press
twice. Then press the
entry uses one digit of memory.
0 9
memory location number ( – ) you
want to clear. A tone sounds.
• If you try to enter more than 16
digits, the phone beeps 5 times
and exits the programming
mode. Start over at Step 2 and
enter no more than 16 digits in
Step 3.
Entering a Pause
In some telephone systems, you must
dial an access code ( , for example)
9
MEM
4. Press
again, then enter the
and wait for a second dial tone before
you can dial an outside number. You
can store the access code with the
phone number. However, you must
also store a pause after the access
code to allow the outside line time to
0 9
memory location number ( – )
where you want to store the num-
ber. A tone sounds to indicate that
the number is stored.
5. For each stored number, write the
person’s or company’s name next
to the appropriate location number
on the supplied MEMORY direc-
tory sticker. (Use a pencil in case
you need to change the number
later.)
REDIAL/P
connect. To do so, press
.
Each press enters a 2-second pause.
REDIAL/P
For a longer pause, press
additional times.
Dialing a Memory Number
6. Attach the sticker to the phone.
To dial a number stored in memory, lift
TALK
the handset or press
. The TALK/
BATT LOW indicator lights.
When you hear a dial tone, simply
MEM
press
and enter the memory loca-
tion number for the number you want
to dial.
Note: If you select an empty memory
location, the phone beeps 5 times. Try
again.
To replace a stored number, simply
store a new number in its place.
15
43-1088_90.fm Page 16 Tuesday, August 17, 1999 2:57 PM
To connect the headset, pull open the
rubber cover marked on the side of
Chain-Dialing Service
Numbers
the handset, then insert the headset’s
3/32-inch plug into the jack.
For quick recall of numbers for special
services (such as alternate long dis-
tance or bank by phone), store each
group of numbers in its own memory
location.
To use the stored special service infor-
mation, dial the service’s main number
first. Then, at the appropriate place in
the call, press MEM and the number for
the location where the additional infor-
mation is stored.
Testing Stored Emergency
Numbers
Notes:
• Connecting a headset discon-
nects the handset’s earpiece and
microphone.
If you store an emergency service’s
number (police department, fire de-
partment, ambulance) and you choose
to test the stored number, make the
test call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
• VOLUME on the handset (see
“Setting the Handset Volume” on
Page 12) also controls the con-
nected headset’s volume.
• If you place the handset on the
base to recharge it while the
headset is connected, be sure the
handset seats properly.
USING A HEADSET
With a headset connected, you make
or answer calls as usual using the keys
on the handset.
You can make or answer calls with
hands-free convenience using an op-
tional headset that has a 3/32-inch plug.
We recommend RadioShack Cat. No.
43-194, which is specially designed for
use with the ET-918/920.
When you finish using the headset,
disconnect it from the handset and
close the rubber cover to protect the
jack.
16
43-1088_90.fm Page 17 Tuesday, August 17, 1999 2:57 PM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, the fol-
lowing suggestions might help.
Problem
Suggestion
Low volume or unusual sounds.
Someone has picked up another phone on
the same line. Hang up the other phone.
If you are using the headset, ensure the
headset plug is properly connected to the
jack.
Severe noise interference.
Press CH to change the channel.
Keep the handset away from computers, re-
mote control toys, wireless microphones,
alarm systems, intercoms, room monitors,
fluorescent lights, and electrical appliances.
Move to another location or turn off the
source of interference.
Hang up and redial the number.
The phone cannot be operated at a use-
ful distance from the base because the
signal becomes weak or noisy (handset’s
range has decreased).
Lift the base’s antenna to a fully vertical posi-
tion.
Be sure neither the handset or base antenna
is touching a metal surface.
Return the handset to the base to recharge
the battery pack.
The phone does not work or works
poorly.
Be sure the base’s phone line cord and AC
adapter are correctly and securely con-
nected, and the battery is charged.
The handset battery does not charge.
Check the charging contacts on the handset
and base. If they are dirty, clean them with a
pencil eraser.
Be sure the battery is properly connected.
Be sure the handset is properly seated on the
base.
17
43-1088_90.fm Page 18 Tuesday, August 17, 1999 2:57 PM
Problem
Suggestion
Handset does not ring or receive a page. Lift the base’s antenna to a fully vertical posi-
tion.
Move the handset closer to the base.
Move the base away from other electrical de-
vices.
Return the handset to the base to recharge
the battery pack.
The handset stops working or works
poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical posi-
tion.
If the base lost power while the handset was
off of it, the security access-protection code
might have changed. With the handset re-
moved from the base, restore power to the
base, then place the handset back on the
base. The CHARGE indicator lights, indicat-
ing that the code is set again.
Be sure the handset’s battery pack is
charged. (If the battery pack power is too low,
it does not have enough power to light the
TALK/BATT LOW indicator.)
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your phone to your local RadioShack store for assistance.
18
43-1088_90.fm Page 19 Tuesday, August 17, 1999 2:57 PM
CARE AND MAINTENANCE
Your ET-918/920 900-MHz Cordless Telephone with Headset Jack is an example of
superior design and craftsmanship. The following suggestions will help you care for
your cordless telephone so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Handle the phone gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the phone to work improperly.
Use and store the phone only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices and
distort or melt plastic parts.
Keep the phone away from dust and dirt, which can cause premature
wear of parts.
Wipe the phone with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the phone.
Modifying or tampering with the phone’s internal components can cause a malfunc-
tion and might invalidate your phone’s warranty and void your FCC authorization to
operate it. If your phone is not performing as it should, take it to your local Ra-
dioShack store for assistance. If the trouble is affecting the phone lines, the phone
company might ask you to disconnect your phone until you have resolved the prob-
lem.
19
43-1088_90.fm Page 20 Tuesday, August 17, 1999 2:57 PM
3. Insert the new battery pack’s plas-
tic connector into the socket in the
compartment and place the bat-
tery pack into the compartment.
REPLACING THE
BATTERY PACK
If you follow the instructions in “Con-
necting and Charging the Battery
Pack” on Page 9, the battery pack
should last about one year. If the bat-
tery does not hold a charge (when the
phone is not in use) for more than 2
hours after an overnight charge, re-
place the battery with a new 3.6 volt,
600 milliamp battery with a connector
that fits the socket in the battery com-
partment. You can order a replace-
ment battery pack through your local
RadioShack store.
4. Replace the cover and tighten the
screw.
Cautions:
• You must use a replacement bat-
tery of the same size and type.
• Do not dispose of the battery in a
fire because it might explode.
• Do not open or mutilate the bat-
tery.
• Be careful not to short the battery
by touching the connector’s pins
with conducting materials, such as
rings, bracelets, and keys. The
battery or conductor might over-
heat and burn.
Install the new battery pack as de-
scribed below, then charge the battery
for about 14 hours (see “Connecting
and Charging the Battery Pack” on
Page 9).
Note: To avoid losing phone numbers
stored in memory, try to install and be-
gin charging the new battery within 3
minutes.
If you have trouble replacing the bat-
tery, take the phone to your local Ra-
dioShack store for assistance.
1. Loosen the screw on the battery
compartment cover on the bottom
of the handset, and slide off the
cover in the direction of the arrow.
Important: This product contains a re-
chargeable nickel-cadmium battery. At
the end of the battery’s useful life, it
must be recycled or disposed of prop-
erly. Contact your local, county, or
state hazardous waste management
authorities for information on recycling
or disposal programs in your area.
Some options that might be available
are: municipal curb-side collection,
drop-off boxes at retailers such as your
local RadioShack store, recycling col-
lection centers, and mail-back pro-
grams.
2. Lift the battery out of the compart-
ment, then gently pull on the bat-
tery connector to disconnect it.
20
43-1088_90.fm Page 21 Tuesday, August 17, 1999 2:57 PM
If you cannot eliminate the interfer-
ence, the FCC requires that you stop
using your phone.
THE FCC WANTS YOU
TO KNOW
In the unlikely event that your phone
causes problems on the phone line,
the phone company can temporarily
discontinue your service. If this hap-
pens, the phone company attempts to
notify you in advance. If advance no-
tice is not practical, the phone compa-
ny notifies you as soon as possible and
advises you of your right to file a com-
plaint with the FCC.
Some cordless telephones operate on
frequencies that might cause interfer-
ence to nearby TVs and VCRs. To
minimize or prevent such interference,
the base of the cordless telephone
should not be placed near or on top of
a TV or VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect
the operation of this telephone. The
telephone company notifies you of
these changes in advance, so you can
take the necessary steps to prevent in-
terruption of your telephone service.
Your telephone has built-in lightning
protection to reduce the risk of damage
from surges in telephone line and pow-
er line current. This lightning protection
meets or exceeds FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
Your phone might cause TV or radio
interference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it. Try to
eliminate the interference by:
Lightning damage is not common.
Nevertheless, if you live in an area that
has severe electrical storms, we sug-
gest that you unplug your phone during
storms to reduce the possibility of
damage.
• Moving your phone away from the
receiver
• Connecting your phone to an AC
outlet that is on a different electri-
cal circuit from the receiver
• Contacting
your
local
Ra-
dioShack store for help
21
43-1088_90.fm Page 22 Tuesday, August 17, 1999 2:57 PM
NOTES
22
43-1088_90.fm Page 23 Tuesday, August 17, 1999 2:57 PM
23
43-1088_90.fm Page 24 Tuesday, August 17, 1999 2:57 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
UDZZ01826BZ
10A7
Printed in the Philipines
|